Innovita Primo 11 LPG Gas Water Heater

Innovita Primo 11 LPG gas water heater

The Innovita Primo 11 LPG gas water heater is a compact wall-mounted instantaneous water heater designed to provide hot water on demand without requiring a conventional storage cylinder.

The Primo 11 delivers up to 12 litres per minute at a 25°C temperature rise and has a maximum output of 19.3 kW when operating at the specified 37 mbar LPG supply pressure.

It combines battery-powered electronic ignition, flame-failure protection, Low-NOx combustion and an ErP A+ energy rating in a compact design suited to approved LPG hot-water installations.

The Primo 11 is particularly relevant to static caravans, holiday homes, park homes, lodges and other suitable off-grid or LPG-powered properties.

Key Features

• Innovita Primo 11 LPG gas water heater
• Instantaneous hot-water production
• Up to 12 L/min at ΔT25°C
• 19.3 kW maximum output
• Approximately 18.6 kW maximum heat capacity
• LPG operation
• 37 mbar LPG supply pressure
• ErP A+ energy rating
• Approximately 89% efficiency at maximum output
• Battery-powered electronic ignition
• No permanent mains electrical supply required for ignition
• Flame-failure protection
• Low-NOx combustion
• Maximum NOx approximately 20 mg/kWh
• Maximum water temperature 60°C
• Operating water pressure 0.2–10 bar
• 110 mm flue
• 1/2-inch BSP water and gas connections
• Compact wall-mounted construction
• Suitable for approved caravan and off-grid applications

Published specifications support these core product characteristics.

12 L/min Instantaneous LPG Water Heater

The Innovita Primo 11 is an instantaneous LPG water heater.

Unlike a storage water heater, it does not rely on a conventional hot-water cylinder that must be heated before use. The burner operates when hot water is required.

The published maximum flow is:

12 L/min at ΔT25°C

Actual flow depends on incoming cold-water temperature, required outlet temperature, water pressure and other operating conditions.

For customers searching for a 12 L/min LPG water heater, the Primo 11 provides a higher flow capacity than the smaller Innovita Primo 6.

19.3 kW LPG Water Heater

The Innovita Primo 11 has a published maximum output of approximately 19.3 kW.

The available technical information lists:

• Minimum heat capacity: approximately 9.8 kW
• Maximum heat capacity: approximately 18.6 kW
• Minimum output: approximately 8.7 kW
• Maximum output: approximately 19.3 kW

These figures should be interpreted according to the specified LPG supply and operating conditions.

LPG Operation at 37 mbar

The Primo 11 LPG model is specified for a 37 mbar LPG supply pressure.

Always verify the gas configuration, supply arrangement and applicable installation requirements for the country where the appliance will be installed.

Gas appliances should be installed and commissioned by an appropriately qualified professional.

A+ ErP Energy Rating

The Innovita Primo 11 is listed with an ErP A+ energy rating.

Published product information also specifies approximately 89% efficiency at maximum output.

The A+ rating is an important commercial specification for customers comparing LPG water heaters for caravan, holiday-home and compact residential applications.

Battery-Powered Electronic Ignition

The Primo 11 uses battery-powered electronic ignition.

This means a permanent mains electrical connection is not required for the ignition system.

Battery operation can be particularly useful for approved caravan and off-grid applications where conventional mains electricity may not be available at the appliance.

Flame-Failure Protection

The Primo 11 includes a flame-failure device designed to shut off the gas supply if the burner flame is lost.

This is an important safety feature for an LPG-fired water heater.

Low-NOx LPG Water Heater

The published specifications list maximum NOx emissions of approximately 20 mg/kWh.

This makes Low-NOx performance an important product specification for customers comparing modern LPG water heaters.

Static Caravan Water Heater

The Innovita Primo 11 LPG water heater is particularly relevant to static caravan applications.

Potential applications include:

• Static caravans
• Holiday homes
• Holiday lodges
• Park homes
• Cabins
• Annexes
• Suitable off-grid properties
• Compact LPG-powered accommodation

Suitability depends on the appliance configuration, installation requirements, ventilation, flue arrangement, water supply and local regulations.

Off-Grid Hot Water

Because the Primo 11 uses battery-powered electronic ignition, it does not require a permanent mains electrical supply for ignition.

This makes it useful for approved LPG hot-water installations where electrical infrastructure is limited.

However, off-grid suitability does not mean that every off-grid installation is automatically suitable. The appliance must be installed according to manufacturer requirements and applicable regulations.

Compact Wall-Mounted Design

The Primo 11 is designed for wall-mounted installation.

Published specifications list approximate dimensions of:

592 × 314 × 246 mm

and an empty weight of approximately:

8.5 kg.

Its compact footprint makes it useful where installation space is limited.

110 mm Flue

The published product specifications list a 110 mm flue diameter for the Primo 11.

The flue arrangement is a critical part of installation because combustion gases must be safely discharged.

Before installation, confirm the exact flue components, route, terminal position, ventilation and clearance requirements against the current product documentation and applicable national regulations.

Morco Water Heater Replacement

One of the strongest commercial search opportunities for this product is Morco replacement searches.

The Innovita Primo 11 is commonly marketed as a replacement option for older Morco models including:

• Morco EUP11
• Morco M11 / Primo 11
• Morco D61B
• Morco D61E

However, a replacement should not be assumed to be a direct installation simply because the model is listed as a replacement.

A qualified installer should confirm:

• Existing appliance
• Gas supply
• Water connections
• Flue arrangement
• Ventilation
• Wall fixing
• Appliance clearances
• Local installation requirements

The available product information specifically identifies these Morco models as replacement applications.

Instant Hot Water Without a Storage Cylinder

The Primo 11 heats water when a hot-water outlet is opened.

Therefore, there is no conventional hot-water storage cylinder that needs to be heated in advance.

This can help make the system particularly suitable for compact accommodation where space is limited.

Actual hot-water performance depends on the appliance settings, incoming water temperature and available water pressure.

Technical Specifications

The specifications above are based on published Primo 11 product information.

Innovita Primo 11 vs Innovita Primo 6

The Primo 11 is the higher-capacity model compared with the Primo 6.

Primo 11

• Up to 12 L/min at ΔT25°C
• Up to 19.3 kW output
• 37 mbar LPG
• A+ ErP rating
• Suitable for higher hot-water demand

Primo 6

• Up to 6 L/min at ΔT25°C
• Approximately 11.6 kW maximum output
• Designed for lower hot-water demand

The Primo 11 is therefore the better option where the installation requires greater instantaneous hot-water flow, provided the water supply and installation conditions are suitable.

Frequently Asked Questions

Is the Innovita Primo 11 an LPG water heater?

Yes. The Primo 11 is an instantaneous LPG gas water heater designed for suitable LPG hot-water installations.

How many litres per minute does the Innovita Primo 11 deliver?

The published maximum is 12 L/min at a 25°C temperature rise. Actual flow depends on operating conditions.

What is the output of the Innovita Primo 11?

The published maximum output is approximately 19.3 kW, with maximum heat capacity of approximately 18.6 kW.

Does the Primo 11 require mains electricity?

No permanent mains electrical supply is required for ignition. The appliance uses battery-powered electronic ignition.

What LPG pressure does the Primo 11 use?

The published LPG supply pressure is 37 mbar.

Is the Innovita Primo 11 suitable for static caravans?

Yes. It is particularly relevant to static caravans and other suitable LPG-powered accommodation, subject to the installation requirements.

Can the Primo 11 replace a Morco EUP11?

The Primo 11 is marketed as a replacement option for the Morco EUP11 and several other older Morco models. However, compatibility must be confirmed by a qualified installer before installation.

Can it replace a Morco D61B?

The D61B is among the older Morco models commonly listed as a replacement application for the Primo 11. Confirm the existing installation and flue arrangement before replacement.

What size flue does the Primo 11 use?

Published specifications list a 110 mm flue. Always confirm the exact supplied components and installation requirements before fitting.

What is the maximum water temperature?

The published maximum water temperature is 60°C.

Is the Primo 11 energy efficient?

The published LPG model specification lists an ErP A+ energy rating and approximately 89% efficiency at maximum output.

Does the Primo 11 have Low-NOx combustion?

Yes. Published specifications list maximum NOx emissions of approximately 20 mg/kWh.

Does the Innovita Primo 11 need professional installation?

Yes. It is an LPG gas appliance and should be installed and commissioned by an appropriately qualified professional according to the manufacturer’s instructions and applicable national regulations.

Buy Innovita Primo 11 LPG Gas Water Heater

The Innovita Primo 11 LPG gas water heater provides up to 12 L/min instantaneous hot water, approximately 19.3 kW maximum output, battery-powered electronic ignition, flame-failure protection, A+ ErP efficiency and Low-NOx combustion.

It is particularly relevant to static caravans, holiday homes, park homes, lodges and suitable off-grid LPG installations.

The Primo 11 is also a strong replacement candidate for older Morco EUP11, M11, D61B and D61E water heaters, although compatibility should always be checked by a qualified installer before replacement.

Choose the correct LPG appliance for your installation and have it installed and commissioned professionally.